100% HDPE sun shade sail/Polyester shade sail/outdoor garden sun shade net
1) Material: VIRGIN high-density polyethylene (HDPE)
2) Block out 90% sunlight. Weight from 160g/m2-460g/m2(100g-350g net+100g-120gfilm)
3) Long life stainless steel D-ring; yarn fabric and reinforced webbing and stitching
4) 5-10 years UV heavy duty warranty
5) Many colors are available
6) Common size:
6x3. 6x3. 6m triangular
3. 6x3. 6m square
1m, 2m, 4m or by requirements.
Green,Black ,Dark green ,Yellow,gray,Blue and white or by requirements.
100% new material (HDPE )
Minimum life length: 2-3years, under normal weather conditions and use.
25-30days after deposite
South America,Japan, the Middle East ,Europe , markets.
Terms of Payment
300 ton/tons per month
Piece in PP bag,several in a carton(or any customized)
Sail shades are design to bring shade into the garden and provide a shelter from the sun's harmful rays. The sail cuts out up to 90% of harmful UV and provides a stylish and pleasant area to enjoy the garden or outdoor play.
How to make a shade sail
Gather your supplies
- Suitably sized and shaped sail (see Notes, below)
- 100mm dia. x 4mm wall thickness galvanised steel posts
- Concrete mix (4 bags per post)
- Suitable stainless-steel fixings for attaching sail to your combination of posts, fasciae and walls. These include eye bolts for posts, pad eyes for wall fixings, external-grade Chemset chemical anchor (if fixing into masonry), U-bolts, strap tensioners, S-hooks, D-shackles, fascia supports and turnbuckles
Lay sail out on ground. For a 5 x 3m sail running parallel to wall, it should be 300mm from wall to allow for tensioning. Mark out positions of posts and wall or fascia fixings, allowing an extra 300 and 500mm from each corner to allow for tensioning. Square and rectangular sails are normally installed as a hyperbola, so diagonally opposite posts or fixing points are high or low.
For each post, dig a 400 x 400mm hole 800-1000mm deep. If ground is firm, lay about 100mm of 20mm aggregate in base of hole. If ground is soft, pour about 100mm of concrete in hole.
Bore a hole near bottom of pole and insert a galvanised steel bolt with nut. This keys post in concrete and stops round posts rotating. Fit a heavy-duty, stainless-steel eye bolt 50-100mm down from top of posts. Use double nuts (1 a lock nut) so it cannot undo.
Stand posts in holes with eye-bolt facing diagonally opposite post. Brace posts with temporary props and ensure they are plumb in 2 directions.
Fill each post hole with a fairly dry concrete mix and tamp concrete well. For most smaller sails (under 5m square), posts can be vertical, but for larger sails, move top of post away from opposite post by 150-200mm, so it leans out from sail slightly to help take the strain. Re-tamp concrete and finish surface with a slight slope away from post so water can drain. Let concrete cure for 24-48 hours.
While concrete cures, secure wall and fascia pad eyes, if required. Never rely on the fascia alone; fit fascia supports to fasciae and rafters first to give adequate strength. If fixing to masonry, use an appropriate anchor system. In many cases, a chemical anchor is ideal, but an alternative is to use epoxy together with a conventional masonry anchor.
Once concrete has cured, spread sail back out on ground. Attach fixings to corners of sail with turnbuckles wound out to as slack as possible (you will need turnbuckles on at least 2 corners). Lift each corner to an eye bolt, then tension sail using turnbuckles or tension straps. If you need to extend length of fixing, use straps. Re-tension fixings as necessary over time and clean sails periodically.
Jiangsu Green full Garden Products CO,LTD is located in Jiangsu, Changzhou. We are a manufacturer of all kinds of HDPE nets which are widely used in agriculture, horticulture, construction and other areas.
Our factory is established in 2009 and we are developing fast now. Our products include pallet net, fishing net, weed mat, shade net, scaffold net, anti-bird net,anti-hail net,olive net and other various warp knitting nets. Our products are mainly exported to Japan, Europe, America, Australia and other countries and we have won a good reputation for high quality and reasonable prices of our products.
Our factory has German high speed warp knitting machines and a complete set of equipment. We can guarantee prompt delivery and good after-sales services.
Since establishment, we have taken "Quality, Price, Until You’re Satisfied" as the service aim of our factory.
We are glad to cooperate with more friends at home and abroad. Please feel free to contact us if you have any requirement or questions. You could call us, send e-mail, or visit our factory. We are always of high honesty to do business with every customer.
Choose us! We can provide perfect service and prompt delivery and competitive prices!
Where are we ?