Brand Name: | ZANBO |
Model Number: | ZK1PA+ZY16-E2 |
Use: | Universal |
Place of Origin: | Guangdong, China (Mainland) |
Operating frequency: | 433.92MHZ |
Operating voltage: | 12V |
Working current: | 9-12mA |
Quiescent current: | 0uA |
Transmitting distance: | 50~100m |
Frequency deviation: | +-02MHZ |
Encoding chips: | PT2262/EV1527/HS301 |
Modulation: | ASK |
Resistance: | 4.7M/430K |
Selling Units: | Single item |
Single package size: | 6.2X3.9X3.5 cm |
Single gross weight: | 0.06 KG |
Item no.: ZK1PA Learning code one channel wireless receiver controller
Feature:
• Brand new and high quality.
• 2 button on the remote control.
• Small volume, high receiving sensitivity, stable and reliable.
• Easy to install and match the transmitter.
• With a hook on the remote control.
• You can turn on or turn off the receiver with transmitter(remote control) from any place within a reliable distance.
• Widely use in auto door, window, entrance access, up and down controller,lifting equipment, alarm system industrial control and security etc.
Technical Data Of Receiver:
• Input voltage: 12V
• Receiver sensitivity: > 110 dbm
• Transmitting distance:> 50-100 m ( open space)
• Decoding mode: MCU software decoding
• Remote storage: 18
• Support remote type: EV1527 learning code
• Working mode: Momentary, toggle, latching time delay (3s,5s ,10s ,20s,60s,2min,5min,10min )
• Output terminal: NO , NC , COM
• Dimension of PCB:43.5 x 32 x 18.2 mm (L,W,H)
• Remote control battery: 2 x 3 V CR2016 button batteries
Package 1 Included: Only 1 EV1527 Learning code remote control * 1pcs
Package 3 Included: remote control * 1 pcs(include battery)
Leaning method:
• Press the learning key on the receiver,immediately press any button on the remote,after receiving signal of receiver,LED flashing indicates successful learning.
• Momentary:pressing the learning key on the receiver for one time,then pressing any key of remote control to learn,it it Momentary
Namely:Pressing the key on the remote control.Relay sucking,loosing key,and relay disconnected
• Toggle:pressing the learning key on the receiver for two times,then pressing any key of remote control to learn,it it Toggle
Namely:pressing the key on the remote control,Relay sucking,pressing an other key on the remote control,and then relay diconnected.
• Latch:pressing the learning key on the receiver for three times,then pressing any key of remote control to learn,it is Latch.
Namely:pressing the key on the remote control,Relay sucking,pressing the key again,and then relay diconnected.
• Time delay mode:Pressing the learning key on the receiver for four times,then pressing any key of remote control to learn,it is time delay 3 seconds.
Namely:Pressing the key on the remote control one time or for long time(do not release),,Relay sucking for 3 seconds then disconnect quickly.
Signal delay below:
1:All not connected,delay 3 second.
2:connect A B pin-delay 5 seconds.
3:connect C D pin-delay 10 seconds.
4:connect A B C D pin-delay 20 seconds
5:connect A B E F pin-delay 2 minutes.
6:connect C D E F pin-delay 5 minutes.
7:connect A B C D pin-delay 10 minutes.
Clearing the code:pressing the key on the receiver for 10s,then LED flashing and becoming off indicates existing information is cleared successfully
Remark:
1.don't operate control buttons rapidly and frequently,because the controller is controlled by microproessor,each operation state will response in 1s.
2.If discover the LED lights darken or remote distance shorter,please replace the power.
3.Receiving antenna must be soft,length neither too long or too short,otherwise, it will affect transmitting distance,please try to straighten the antenna,do not near the metal objects
NOTE:
The system can store for 18 pcs of remote,if the remote get more than 18 pcs,the initial remote control will belost.